HOMCOM 3 Piece Pub Table and Chair Set Assembly Manual (SKU:835-135V80DR)

The HOMCOM 3 Piece Pub Table and Chair Set features a sturdy metal frame paired with clean, minimal panels that suit dining areas, kitchens, or compact living spaces. Designed for everyday use, this set combines stability with a streamlined look. With clear step-by-step instructions and clearly labelled components, assembly is straightforward when completed in the correct sequence.

Warning & Safety Instructions

Before beginning the assembly process, please carefully read and follow these safety guidelines:

• Keep children and pets away during assembly.
• Ensure all parts and hardware are present before starting.
• Do not use the product if any part appears damaged or defective.
• Assemble the table and chairs on a flat, stable surface.
• Place a soft cloth or cardboard underneath to prevent floor scratches.
• Adult assembly is required.
• Do not exceed the maximum weight capacity of the table or chairs.

Unboxing Your Set: What’s Included

Parts List

Hardware List

Step 1: Assemble the Chair Side Frame

1. Place Left Side Chair Frame (A) and Right Side Chair Frame (B) upright on a flat, stable surface, positioning them parallel to each other as shown in the diagram.
2. Insert the two Apron (J) between the upper inner sections of the chair frames, aligning the pre-drilled holes on both sides.
3. Position the Lower Support H-Frame (H) between the lower sections of the chair frames, ensuring it sits evenly and aligns with the mounting holes.
4. Insert M6×35 Screws (M) through the aligned holes at each connection point.
5. Use the Allen Key (O) to tighten the screws securely, but do not overtighten.
6. Repeat this process for the second chair.

Step 2: Attach the Chair Seat and Backrest Panel

1. Place the Chair Seat Panel (E) onto the top of the assembled chair frame, ensuring it sits evenly and the mounting holes underneath align with the frame holes.
2. From beneath the seat frame, insert M6×30 Screws (L) into the aligned holes and tighten them using the Allen Key (O) to secure the seat panel firmly.
3. Position the Chair Backrest Panel (G) against the upper rear section of the chair frame, aligning its holes with the pre-drilled holes on the frame.
4. Insert M6×12 Screws (K) through the backrest panel into the frame and tighten evenly with the Allen Key (O).
5. Repeat this process for the second chair.

Chair Assembly Complete

Both chairs are now fully assembled.

• Place each chair upright on a flat, stable surface.
• Check that all legs sit evenly on the floor without wobbling.
• Inspect all screws on the seat, backrest, and frame connections.
• Retighten any loose fasteners using the Allen Key (O) if needed.

Once stability is confirmed, set the chairs aside carefully.

Step 3: Assemble the Table Frame

1. Place both Table Side Leg Frames (C) upright on a flat surface, positioning them parallel to each other as shown in the diagram.
2. Attach the two Table Skirts (F) to the upper inner sides of the leg frames. Align the holes and secure each side using M6×12 Screws (K) and M6×40 Screws (N) where indicated.
3. Position the Stretcher (I) between the lower sections of the leg frames, ensuring it sits straight and aligns with the mounting holes.
4. Insert M6×35 Screws (M) through the leg frames into the center stretcher.
5. Tighten all screws using the Allen Key (O), making sure the table frame remains square and stable.

Note:
Do not fully tighten all screws until the entire frame is correctly aligned. 

Step 4: Attach the Table Top Panel

1. Carefully place the Table Top Panel (D) onto the assembled table frame, making sure it sits evenly on all sides.
2. Align the pre-drilled holes on the underside of the tabletop with the mounting holes on the table frame.
3. From underneath the frame, insert M6×30 Screws (L) into each aligned hole.
4. Tighten all screws using the Allen Key (O) until the tabletop is securely fixed to the frame.

Final Check:
Ensure the table stands evenly without rocking. Recheck all fasteners and tighten if necessary. The table assembly is now complete.

Final Arrangement: Set Placement Complete

• Place the table in its intended position on a flat, stable surface.
• Position one chair neatly on one side of the table.
• Place the second chair on the opposite side, aligning both chairs evenly with the table.
• Check that all legs rest firmly on the floor and the set remains balanced.

Your assembly is now complete and the bar table and chair set is ready for use.

Troubleshooting Guide

Care & Maintenance

• Clean surfaces with a soft, dry or slightly damp cloth
• Avoid abrasive cleaners or harsh chemicals
• Periodically check and retighten screws
• Use the set indoors only and on level flooring
• Avoid excessive moisture exposure

With its balanced structure and compact design, the 3 Piece Pub Table and Chair Set (SKU:835-135V80DR) offers dependable everyday performance. Correct assembly and routine maintenance will help ensure long-lasting stability and comfort.

You can also download the 3 Piece Pub Table and Chair Set assembly manual for reference.

FAQs