This Industrial 4 Piece Dining Set includes a sturdy table, a matching bench with a wire shelf, and two chairs designed for everyday comfort and durability. With clearly labeled parts and straightforward construction, the setup process is simple and can be completed efficiently.
Safety & Preparation
Before starting, keep these important points in mind:
- Assemble on a flat, clean, and soft surface to avoid scratches.
- Do not use power tools; hand tightening is recommended.
- Keep children and pets away during assembly.
- Check all components before starting.
Unboxing: Parts & Hardware Included
Make sure all parts are present before beginning assembly.
Parts List
| No. | Part Name | Quantity |
| 1 | Table Leg Frames | 2 |
| 2 | Table Support Rails | 2 |
| 3 | Tabletop | 1 |
| 4 | Bench Leg Frames | 2 |
| 5 | Bench Support Rails | 2 |
| 6 | Bench Wire Shelf | 1 |
| 7 | Bench Seat | 1 |
| 8 | Left Chair Side Frame | 2 |
| 9 | Right Chair Side Frame | 2 |
| 10 | Chair Support Rails | 4 |
| 11 | Chair Seat | 2 |
| 12 | Chair Backrest | 2 |
Hardware List
| Code | Hardware Name | Quantity |
| A | M6×12 Bolt | 8 |
| B | M6×30 Bolt | 8 |
| C | M6×40 Bolt | 20 |
| D | M6×50 Bolt | 4 |
| E | M6×60 Bolt | 8 |
| F | Allen Key | 1 |
Step-by-Step Assembly Instructions
Step 1: Assemble the Chair Frame
- Take Left Chair Side Frame (8) and Right Chair Side Frame (9) and position them facing each other upright.
- Insert Chair Support Rails (10) between the two side frames as shown in the diagram.
- Align all pre-drilled holes carefully on both sides.
- Use M6×40 Bolts (C) to secure the support rails to the side frames.
- Tighten the bolts evenly using the Allen Key (F), but do not fully tighten yet until all connections are aligned.
Repeat this step for the second chair.
Step 2: Attach the Chair Seat
- Take the assembled chair frame from Step 1 and turn it upside down.
- Position the Chair Seat (11) onto the frame, aligning it with the pre-drilled holes.
- Ensure the seat sits evenly across both Left Chair Side Frame (8) and Right Chair Side Frame (9).
- Insert M6×30 Bolts (B) through the frame into the seat as shown in the diagram.
- Tighten all bolts using the Allen Key (F) until the seat is securely fixed.
Repeat this step for the second chair.
Step 3: Attach the Chair Backrest (Repeat for Both Chairs)
- Turn the chair upright.
- Position the Chair Backrest (12) at the rear of the assembled chair frame.
- Align the backrest with the mounting points on both Left Chair Side Frame (8) and Right Chair Side Frame (9).
- Ensure the holes are properly aligned before inserting bolts.
- Insert M6×12 Bolts (A) into the side mounting points as shown in the diagram.
- Tighten all bolts evenly using the Allen Key (F) until the backrest is firmly secured.
Repeat the same step for the second chair.
Step 4: Assemble the Bench Frame and Shelf
- Take Bench Leg Frames (4) and position them upright, parallel to each other.
- Connect them using Bench Support Rails (5) on both sides as shown in the diagram.
- Align all holes properly before inserting bolts.
- Place the Bench Wire Shelf (6) on the lower support level between the frames.
- Secure all connections using M6×40 Bolts (C) and tighten with the Allen Key (F).
- Ensure the structure is level and all bolts are evenly tightened.
Step 5: Attach the Bench Seat
- Place the Bench Seat (7) on the floor with the underside facing up.
- Take the assembled bench frame from Step 4 and carefully place it on top of the seat.
- Align the frame with the pre-drilled holes on the seat.
- Insert M6×40 Bolts (C) through the frame into the seat as shown in the diagram.
- Tighten all bolts using the Allen Key (F) until securely fixed.
Step 6: Assemble the Table Frame
- Take Table Leg Frames (1) and position them parallel to each other.
- Connect the legs using Table Support Rails (2) on all sides as shown in the diagram.
- Align the holes on the rails with the leg frames carefully.
- Insert M6×60 Bolts (E) into each connection point.
- Tighten all bolts using the Allen Key (F), ensuring the frame is stable and evenly aligned.
Step 7: Attach the Tabletop
- Place the Tabletop (3) on the floor with the underside facing up.
- Take the assembled table frame from Step 6 and carefully place it on top of the tabletop.
- Align the frame with the pre-drilled holes on the tabletop.
- Insert M6×50 Bolts (D) through the frame into the tabletop as shown in the diagram.
- Tighten all bolts using the Allen Key (F) until securely fixed.
Assembly Complete
- Carefully turn all assembled pieces upright if not already done.
- Check that all bolts are fully tightened using the Allen Key (F).
- Ensure the Table, Bench, and Chairs are stable and level on the floor.
- Place the set in your desired location and adjust positioning if needed.
Your dining table, bench, and chair set is now fully assembled and ready for use.
Troubleshooting Guide
| Issue | Possible Cause | Solution |
| Table or bench feels unstable | Loose bolts | Tighten all bolts evenly |
| Parts not aligning | Bolts tightened too early | Loosen, align, then retighten |
| Chair wobbling | Uneven frame assembly | Check side frame alignment |
| Shelf not secure | Incorrect bolt usage | Recheck correct bolt size |
Care & Maintenance
- Clean with a soft, damp cloth.
- Avoid harsh chemicals.
- Regularly check and tighten bolts.
- Keep in a dry environment.
- Do not overload the wire shelf.
With proper assembly and care, your dining set will provide long-lasting stability, comfort, and everyday functionality.
You can also download the HOMCOM Industrial 4 Piece Dining Set full assembly manual for reference.
FAQs
Solid wood and metal are among the most durable options, offering strength and long-term reliability with proper care. Engineered wood can also perform well when finished properly. Choosing a material that resists scratches and moisture helps extend lifespan.
Rectangular and round tables are the most practical for daily use, offering good seating flow and easy placement in most spaces. Round tables encourage conversation, while rectangular ones maximise seating. The choice depends on room layout and routine use.
Using placemats, coasters, and tablecloths helps prevent scratches, heat marks, and spills from damaging the surface. Regular cleaning with a soft cloth maintains its finish over time. Avoid dragging heavy items to reduce surface wear.