The Ottoman with Cushioned Top SKU:F-NHA-6606000BGE is a residential indoor seating piece featuring a padded bench seat supported by dual side frames and stabilizing rails. Designed for structural balance and modern styling, this unit requires proper alignment of the mounting positions to ensure stability and long-term durability. Assembly takes approximately 30 minutes with two adults.
⚠️ Warning & Safety Instructions
Before beginning assembly, review the following safety guidelines:
- For indoor residential use only
- Not intended for commercial use
- Do not assemble on carpet or soft flooring
- Assemble on a clean, non-marring surface
- Two adults are required for safe assembly
- Do not allow children to climb or jump on the bench
- Use only on a flat, level surface
- Do not place near heating vents or direct sunlight
- Do not use harsh cleaners or place hot items directly on the surface
Unboxing: What’s Included
Remove all components from the packaging and verify contents before starting.
Parts
Hardware List
Assembly Preparation
- Keep hardware separated and organized
- Do not fully tighten bolts until instructed
- Save packaging materials until assembly is complete
Step-by-Step Assembly Instructions
Step 1: Attach Rails to Side Frame
- Place one Side Frame (B) on a clean, non-marring surface with the mounting side facing inward.
- Position one Rail (C) against the upper mounting point of the Side Frame (B), aligning the bolt holes.
- Insert Bolt (① M8×45mm) through the aligned holes.
- Tighten using the Allen Key (④).
- Repeat the same process on the opposite upper joint as shown in the diagram.
- Do not fully tighten the bolts at this stage to allow adjustment in later steps.
Step 2: Attach Rails to Second Side Frame
- Place the partially assembled frame from Step 1 on a clean, non-marring surface as shown.
- Ensure the open ends of the Rails (C) are facing upward and aligned properly.
- Align the remaining Side Frame (B) with the open ends of both Rails (C).
- Insert Bolt (① M8×45mm) through the aligned mounting holes.
- Tighten using the Allen Key (④).
- Repeat for both rail connection points.
Do not fully tighten the bolts at this stage.
Step 3: Position the Bench Seat
- Place the Bench Seat (A) facedown on a clean, non-marring surface to protect the upholstery.
- Carefully lift the assembled frame (Side Frames B with Rails C attached).
- Align the mounting holes on the Side Frames (B) with the pre-drilled mounting points on the underside of the Bench Seat (A).
- Ensure all holes are properly aligned before inserting any bolts.
Step 4: Secure the Bench Seat to the Frame
- Insert Bolt (① M8×45mm) through the mounting holes on the Side Frame (B) into the underside of the Bench Seat (A).
- For each bolt, place a Spring Washer (②) followed by a Washer (③) as shown in the diagram.
- Tighten using the provided Allen Key (④).
- Install all bolts loosely at first to ensure proper alignment.
- Once all bolts are inserted, tighten them fully in a sequential manner, alternating sides to ensure even pressure and stability.
Proper sequential tightening prevents frame distortion and ensures long-term structural balance.
Step 5: Stand Bench Upright & Install Plastic Feet
- With assistance from another adult, carefully turn the assembled bench upright.
- Locate the mounting holes at the bottom of each Side Frame (B).
- Insert the Plastic Feet (⑤) into the designated mounting positions by hand.
- Press firmly until each foot is fully seated and secure.
Step 6: Final Check & Ready for Use
- Ensure all bolts are fully tightened and secure.
- Confirm the bench sits evenly on a flat, level surface.
- Check that there is no wobbling or movement in the frame.
Your bench is now fully assembled and ready for use.
Troubleshooting Guide
| Issue | Possible Cause | Solution |
| Bench wobbles | Bolts unevenly tightened | Retighten in sequence |
| Frame misaligned | Rails installed on incorrect side | Reposition rails correctly |
| Seat not flush | Mounting holes not aligned | Loosen, realign, retighten |
| Feet not stable | Plastic feet not fully inserted | Press firmly into place |
Care & Maintenance
- Dust regularly with a clean, lint-free cloth
- Clean spills immediately using mild soap and damp cloth
- Avoid direct sunlight exposure
- Do not use abrasive cleaners or polish
- Keep away from heating or cooling vents
- Do not place hot objects directly on surface
With proper assembly and maintenance, your Ottoman with Cushioned Top (SKU: F-NHA-6606000BGE) will provide stable, durable seating for everyday residential use.
You can also download the official Ottoman with Cushioned Top assembly manual for your reference.
FAQs
Yes, a cushioned ottoman can function as a coffee table when paired with a sturdy tray to create a flat surface for drinks, books, or décor. It works especially well in smaller living rooms where flexibility matters. Choose a firm, well-supported design to prevent sinking under weight.
Cushioned ottomans can lose shape if made with low-density foam or frequently exposed to heavy pressure. High-density foam and reinforced internal frames help maintain structure for years. Regularly rotating and lightly fluffing the cushion can also extend its lifespan.
Vacuum the surface weekly to remove dust and debris, then spot-clean spills immediately with mild fabric-safe cleaner. Always blot instead of rubbing to prevent spreading stains. For deeper cleaning, check the care label or use a professional upholstery service if needed.