The Outsunny Folding Ice Cooler Table with Drain is a multi-functional outdoor table designed to keep your drinks chilled and organized. Featuring a spacious cooler, built-in drain, and convenient storage shelf, this table is perfect for BBQs, picnics, and outdoor parties. Its foldable design makes it easy to store and transport, while the drain system ensures hassle-free water management. Whether you’re hosting a family gathering or tailgating, this table brings both convenience and fun.
Warning & Safety Instructions
Before assembling or using this sink table, carefully review the following safety guidelines:
- For outdoor domestic use only
- Place the table on a flat, stable surface
- Ensure all folding legs are fully locked before use
- Do not sit, stand, or lean heavily on the sink
- Keep hands clear of folding joints during setup
- Always check that drainage components are properly secured before using water
Unboxing Your Sink Table: What’s Included
Parts List
| Part | Qty | Description |
| A | 1 | Drain Cover / Drain Cap |
| B | 1 | Drain Screw |
| C | 1 | Drain Strainer |
| D | 2 | Sealing Ring / Rubber Gasket |
| E | 1 | Drain Connector |
| F | 1 | Drain Connector Washer |
| G | 1 | Drain Lock Nut |
| H | 1 | Drain Pipe |
| I | 1 | Wire Shelf |
| J | 1 | Table Skirt |
| K | 8 | Hook-and-Loop Fastener Strips |
| L | 1 | Sink Table Body / Main Table Frame |
Step-By-Step Assembly Instructions
Step 1: Open and Lock the Folding Legs
- Carefully remove the Sink Table Body (L) from the packaging and place it upside down on a protected surface.
- Open each folding leg outward until it fully extends.
- Pull up the frame connectors underneath the table and lock them securely into position.
Note: Make sure all legs are fully locked before turning the table upright.
Step 2: Install the Sink Drain System
a) Assemble the Drain at the Sink Opening (Top to Bottom)
- Place Sealing Ring (D) on the top side of the sink drain hole, inside the sink.
- Position the Drain Strainer (C) directly on top of the sealing ring.
- From underneath the sink, place the second Sealing Ring (D) against the sink base.
- Attach the Drain Connector (E) beneath the sink so it sits firmly against the lower sealing ring.
- Insert the Drain Screw (B) from the top, passing it through the strainer (C), and tighten it until it securely locks into the drain connector (E).
- Once tightened, place the Drain Cover (A) on top of the strainer as the finishing cover.
b) Connect the Drain Pipe Under the Table
- Slide the Drain Lock Nut (G) onto the Drain Pipe (H) first.
- Place the Drain Connector Washer (F) between the nut and the drain connector to prevent leaks.
- Insert the drain pipe (H) into the Drain Connector (E) and tighten the lock nut (G) until the connection is secure.
Tip: Hand-tighten all components firmly, but avoid over-tightening to protect the sealing rings.
Step 3: Install the Bottom Wire Shelf
- Make sure the table is standing upright on a flat surface with all legs fully locked.
- Take the Wire Shelf (I) and hold it horizontally beneath the sink table.
- Align both ends of the wire shelf with the support rails located between the table legs.
- Slide the wire shelf inward from one side until it rests evenly on both support brackets.
- Adjust the shelf so it sits flat and centered under the table.
- Press gently to ensure the shelf is fully seated and does not shift.
Check: The shelf should feel stable and level, with no wobbling.
Step 4: Attach the Table Skirt Using Hook-and-Loop Strips
- Take the Hook-and-Loop Fastener Strips (K).
- Evenly attach all 8 strips (K) around the outer edge of the sink table, as shown in the image.
- Press each strip firmly to ensure it sticks properly to the table surface.
- Once all strips are in place, take the Table Skirt (J).
- Align the skirt with the fastener strips around the table edge.
- Press the skirt firmly against the strips so it attaches securely on all sides.
- Adjust the skirt as needed to make sure it sits straight and evenly around the table.
Check: Make sure the skirt is fully secured and does not peel away during use.
Troubleshooting Guide
| Issue | Possible Cause | Solution |
| Water leaking underneath | Drain parts loose | Tighten drain screw and lock nut |
| Poor water drainage | Strainer clogged | Clean debris from drain strainer |
| Skirt not staying in place | Fastener strips misaligned | Reposition and press firmly |
Care & Maintenance
- Clean the cooler regularly to prevent mold or bacteria buildup.
- Drain the cooler after each use to prevent standing water.
- Store the table in a cool, dry place to prevent rust.
- Tighten screws periodically to ensure stable assembly.
With its durable materials, easy fold-up design, and functional drainage system, the Outsunny Folding Ice Cooler Table with Drain SKU:84G-618V00TN will make your outdoor events more enjoyable and organized. Keep the table maintained for long-lasting performance and it will serve you well for many future gatherings.
You can also download the Outsunny Folding Ice Cooler Table with Drain SKU:84G-618V00TN for your reference.
FAQs
1. How much weight can a folding ice cooler table support?
Most folding ice cooler tables are designed to hold between 50–100 lbs on the tabletop, depending on the build quality and materials used. The cooler compartment itself can also support some weight when closed, but it’s best to avoid placing very heavy items on top.
2. Is a folding ice cooler table weather‑resistant?
Many folding ice cooler tables are made with weather‑resistant materials like powder‑coated steel, aluminum, or durable plastics that stand up well to outdoor conditions. This helps protect them from rain, sun exposure, and rust during regular use.
3. Can a folding ice cooler table be used for hot items?
Folding ice cooler tables are primarily designed for cold storage and serving cold beverages or food. Placing hot items directly on the surface or inside the cooler can damage the insulation or surface finish. If you need a table for hot dishes, use heat‑resistant trivets or choose a separate table designed for heat.