HOMCOM Round Coffee Table Set of 2 Assembly Manual (SKU:839-151BN)

The HOMCOM Round Coffee Table includes a large table and a matching small table, designed with sturdy leg frames and cross-frame supports for everyday stability. Each table features a round tabletop paired with a reinforced base structure that ensures balance and reliable load support. The assembly process is straightforward, using clearly labeled components and minimal hardware. Following the steps in sequence will ensure proper alignment, structural strength, and a clean finished look.

⚠️ Warning & Safety Instructions

Before beginning assembly, carefully review the following safety guidelines:

• Assemble on a flat, stable, and level surface
• Keep children and pets away during assembly
• Do not use the product if any part is damaged or missing
• Avoid overtightening bolts to prevent frame distortion
• Use only the provided hardware and tools

Unboxing: What’s Included

Remove all components from the package and verify that all parts and hardware listed below are present before starting assembly.

Parts List

Hardware List

Step-by-Step Assembly Instructions

Step 1: Attach Large Table Cross-Frame to the Large Table Leg Frame

• Stand the Large Table Leg Frame (3) upright so it is perpendicular to the floor, as shown in the diagram.
• Take one Large Table Cross-Frame (2) and position it in the centre of the leg frame, aligning its mounting holes with the right side centre set of holes on the frame.
• Match the holes so the cross-frame lines up with the right centre holes above and right centre holes below.
• Insert M6×40 Bolts (A) into the aligned holes (use the positions shown) and tighten using the Allen Key (C).

Step 2: Install the Second Large Table Cross-Frame

• Keep the Large Table Leg Frame (3) standing upright and perpendicular to the floor as assembled in Step 1.
• Take the second Large Table Cross-Frame (2) and position it on the opposite side of the centre cross-frame, as shown in the diagram.
• Align the mounting holes of the cross-frame with the remaining upper and lower centre holes on the leg frame.
• Insert M6×40 Bolts (A) through the aligned holes.
• Tighten the bolts securely using the Allen Key (C).

Ensure both large table cross-frames are parallel, evenly spaced, and firmly fixed to the leg frame

Step 3: Attach the Large Circular Tabletop

• Carefully turn the assembled Large Table Leg Frame (3) with both installed Large Table Cross-Frames (2) upside down.
• Position the Large Circular Tabletop (1) on a flat, protected surface with the underside facing upward.
• Align the mounting holes on the tabletop with the holes on the leg frame base.
• Insert M6×30 Bolts (B) through the tabletop into the frame, as shown.
• Use four M6×30 Bolts (B) in total, securing all marked connection points.
• Tighten the bolts evenly using the Allen Key (C).

Ensure the tabletop is centred correctly and fully secured before turning the table upright.

Step 4: Turn the Large Table Upright

• Carefully lift the assembled large table and turn it upright onto its legs.
• Place the table on a flat, level surface and ensure all legs rest evenly on the floor.
• Check that the Large Circular Tabletop (1) is secure and that the Large Table Leg Frame (3) stands straight without wobbling.
• The large table assembly is now complete and ready for use.

Step 5: Attach the Small Table Cross-Frame to the Small Table Leg Frame

• Stand the Small Table Leg Frame (6) upright so it is perpendicular to the floor, as shown in the diagram.
• Take the Small Table Cross-Frame (5) and position it in the right centre of the leg frame, aligning its holes with the upper and lower centre holes on the frame.
• Insert M6×40 Bolts (A) through the aligned holes.
• Use two bolts (A) in total, one at the top and one at the bottom.
• Tighten securely using the Allen Key (C).

Step 6: Install the Second Small Table Cross-Frame

• Keep the Small Table Leg Frame (6) standing upright and perpendicular to the floor as assembled in Step 5.
• Take the second Small Table Cross-Frame (5) and position it on the opposite side of the first cross-frame, aligning it with the remaining centre mounting holes on the leg frame.
• Align the cross-frame holes with the upper and lower centre holes on the leg frame.
• Insert M6×40 Bolts (A) into the aligned holes.
• Use two bolts (A) in total.
• Tighten securely using the Allen Key (C).

Step 7: Attach the Small Circular Tabletop

• Carefully turn the assembled Small Table Leg Frame (6) with both installed Small Table Cross-Frames (5) upside down.
• Place the Small Circular Tabletop (4) on a flat, protected surface with the underside facing upward.
• Align the mounting holes on the tabletop with the holes on the leg frame.
• Insert M6×30 Bolts (B) through the tabletop into the leg frame.
• Use four M6×30 Bolts (B) in total, securing all marked connection points.
• Tighten the bolts evenly using the Allen Key (C).

Step 8: Final Check and Assembly Complete

• Place both the large table and the small table upright on a flat, level surface, as shown.

The large and small circular tables are now fully assembled and ready for use.

Troubleshooting Guide

Care & Maintenance

• Wipe tabletops regularly with a soft, dry or slightly damp cloth
• Avoid abrasive cleaners or harsh chemicals
• Periodically check bolt tightness and retighten if needed
• Do not sit or stand on the tables
• Keep tables in dry, indoor conditions to maintain finish

With its circular design and reinforced cross-frame construction, this HOMCOM Round Coffee Table Set of 2 delivers dependable stability and everyday functionality. Assembling each component carefully and in order ensures proper alignment, durability, and a balanced final setup.

You can also download the official HOMCOM Round Coffee Table set assembly manual for additional reference.

FAQs