The HOMCOM Wooden Dining Chair is designed with a classic spindle-back style and a sturdy wood frame, making it a practical seating choice for dining rooms, kitchens, or breakfast nooks. The chair uses a simple four-step assembly process with clearly labeled parts and hardware. By following the instructions in the correct order, you can complete assembly efficiently while ensuring proper stability and alignment.
Warning & Safety Instructions
Before beginning assembly, carefully review the following safety guidelines:
- For indoor household use only
- Assemble on a flat, stable surface
- Keep children and pets away during assembly
- Do not use the chair if any part is damaged or missing
- Do not exceed the recommended weight capacity
- Be cautious of pinch points during assembly
Unboxing Your Chair: What’s Included
Before starting, remove all items from the box and verify that all parts and hardware are present.
Parts List
| Part No. | Quantity | Description |
| 1 | 4 | Chair Backrest |
| 2 | 4 | Chair Seat Panel |
| 3 | 4 | Left Leg Frame |
| 4 | 4 | Right Leg Frame |
| 5 | 4 | Spindle |
Hardware List
| Hardware | Quantity | Description |
| A | 12 | M6 × 40mm Hex Bolts |
| B | 12 | Spring Washers |
| C | 12 | Flat Washers |
| D | 1 | Allen Key |
| E | 24 | Screws |
| F | 8 | M6 × 50mm Hex Bolts |
| G | 8 | Barrel Nuts |
Step 1: Attach the Chair Backrest to the Chair Seat Panel
- Stand the Chair Seat Panel (2) upright on a flat surface so the panel is perpendicular (vertical) to the floor, with the pre-drilled holes facing outward.
- Position the Chair Backrest (1) next to the seat panel and align the three side holes on the backrest with the matching holes on the edge of the seat panel.
- Prepare the fasteners for each connection:
- Insert one Spring Washer (B) and one Flat Washer (C) onto one M6 × 40mm Hex Bolt (A).
- Insert the bolts through the seat panel into the backrest (3 bolts total).
- Hand-tighten first to keep the parts aligned.
- Use the Allen Key (D) to tighten the bolts evenly, alternating between them to keep the backrest straight and flush.
Step 2: Connect the Left and Right Leg Frames with the Spindle
- Place the Left Leg Frame (3) and Right Leg Frame (4) upside down on a flat surface, keeping them parallel and spaced apart.
- Insert the Spindle (5) between the two leg frames, aligning the holes on each end of the spindle with the holes on the inner sides of the leg frames.
- Insert one Barrel Nut (G) into the round opening on each side of the spindle. Make sure the barrel nut hole is aligned with the bolt path.
- Slide one M6 × 50mm Hex Bolt (F) through each leg frame and into the barrel nut inside the spindle.
- Hand-tighten both bolts first to keep the spindle centered.
- Use the Allen Key (D) to tighten both bolts securely, alternating sides to ensure even alignment.
Important:
Confirm that the spindle sits straight between the leg frames before fully tightening. This connection provides structural stability for the chair, so ensure both bolts are firmly secured.
Step 3: Attach the Seat and Backrest Assembly to the Leg Frame
- Turn the leg frame assembly upside down, with all four legs pointing upward and the spindle centered.
- Lower the assembled Chair Seat Panel (2) with the attached Chair Backrest (1) onto the leg frame, aligning the pre-drilled holes on the underside of the seat panel with the mounting holes on the leg frames.
- Insert the Screws (E) through the leg frame brackets and into the seat panel (6 screws total), as shown in the diagram.
- Hand-tighten all screws first to ensure the seat is properly aligned on the frame.
- Use the Allen Key (D) to tighten all six screws evenly, alternating between sides to keep the seat level and centered.
Repeat the all above steps to assemble the remaining chairs.
Final Step: Assembly Complete
- Carefully turn the chair upright and place it on a flat, stable surface.
- Check all connection points, ensuring every bolt and screw is fully tightened.
- Inspect the chair’s stability by gently pressing on the seat and backrest.
- Confirm all four legs rest evenly on the floor without wobbling.
Your chair is now fully assembled and ready for use.
Troubleshooting Guide
| Issue | Possible Cause | Solution |
| Chair feels unstable | Hardware not fully tightened | Retighten all bolts evenly |
| Chair wobbles | Uneven leg alignment | Loosen screws, realign, retighten |
| Spindle misaligned | Barrel nut not seated correctly | Reinsert barrel nut and bolt |
| Screws hard to install | Holes not aligned | Adjust positioning before tightening |
Care & Maintenance
- Clean with a soft, dry, or slightly damp cloth
- Avoid abrasive cleaners or harsh chemicals
- Periodically check and retighten hardware
- Use only on level indoor flooring
- Keep away from excessive moisture
With its timeless design and simple construction, the HOMCOM Wooden Dining Chair (SKU: 83A-328V01) offers dependable seating and easy assembly. Following these steps ensures long-term stability and comfort.
You may also download the HOMCOM Wooden Dining Chair (SKU: 83A-328V01) assembly manual for your reference.
FAQs
Yes, wooden chairs are comfortable for everyday use, especially with contoured designs or cushions. Well-made wood chairs provide good support for regular meals. For extended sitting, add padded seat cushions for extra comfort.
Neither is better, it depends on your needs. Wood offers warmth and timeless style, while metal provides durability and modern aesthetics. Choose based on your décor preference and budget.
Yes, but attach felt pads to the chair legs to prevent scratches. These protectors also reduce noise and help chairs glide smoothly. Without them, you risk damaging both chairs and floors.