The Outsunny Rocking Chair & Glass Table Set combines two comfortable rocking chairs with a matching round glass-top table, designed for relaxed seating and balanced outdoor use. The curved rocking bases provide smooth motion, while the reinforced table frame ensures stable support for drinks and accessories. With clearly labeled components and minimal hardware, the assembly process is structured and efficient when completed in sequence.
⚠️ Warning & Safety Instructions
Before beginning assembly, carefully review the following guidelines:
- Assemble on a flat, stable, and level surface
- Do not fully tighten bolts until all parts are connected
- Keep children and pets away during assembly
- Do not use the product if any part is damaged or missing
- Avoid overtightening bolts to prevent frame distortion
- Ensure all washers are used as instructed for secure fastening
Unboxing: What’s Included
Remove all components from the package and verify that all parts and hardware listed below are present before starting assembly.
Parts List
| Code | Part Name | Quantity |
| A | Chair Seat | 2 |
| B | Left Leg Frame | 2 |
| C | Right Leg Frame | 2 |
| D | Seat Cushion | 2 |
| E | Back Cushion | 2 |
| F | Table Top Frame | 1 |
| G | Table Legs | 3 |
| H | Glass Table Top | 1 |
Hardware List
| Code | Hardware | Quantity |
| I | Washers | 22 |
| J | M6×20 Bolts | 22 |
| K | Allen Key | 1 |
Step 1: Attach the Left and Right Leg Frames to the Chair Seat
- Place the Chair Seat (A) upside down on a clean, protected surface to prevent scratches.
- Position the Left Leg Frame (B) on the left side of the seat base and the Right Leg Frame (C) on the right side, aligning the mounting holes at the four connection points shown in the diagram.
- For each connection point:
- Insert one Washer (I) onto an M6×20 Bolt (J).
- Insert the bolt through the aligned hole in the leg frame into the Chair Seat (A).
- Use 8 M6×20 Bolts (J) and 8 Washers (I) per chair (16 total bolts and washers for both chairs).
- Tighten the bolts using the Allen Key (K), but do not fully tighten until all bolts are inserted and properly aligned.
- Repeat this step one more time.
Step 2: Install the Seat and Back Cushions
- Once the chair frame is fully assembled and placed upright on a flat surface, begin installing the cushions.
- Place the Seat Cushion (D) onto the Chair Seat (A), ensuring it sits evenly within the frame and aligns with the front and side edges.
- Next, position the Back Cushion (E) against the curved backrest, sliding it gently into place so it rests securely against the frame.
- Press both cushions lightly to confirm they are stable and properly aligned.
- Repeat the same process for the second chair.
Step 3: Attach the Table Legs to the Table Top Frame
- Place the Table Top Frame (F) upside down on a flat, protected surface to prevent scratching.
- Position each Table Leg (G) at the three designated mounting points underneath the frame. Align the holes on the leg brackets with the pre-drilled holes on the frame.
- For each leg connection:
- Place one Washer (I) onto an M6×20 Bolt (J).
- Insert the bolt through the leg bracket into the frame mounting hole.
- Use a total of 6 M6×20 Bolts (J) and 6 Washers (I) to secure all three legs.
Tighten the bolts using the Allen Key (K), but do not fully tighten until all legs are attached and properly aligned.
Step 4: Install the Glass Table Top
- After securing the Table Legs (G) to the Table Top Frame (F) and tightening all bolts evenly, carefully turn the table upright and place it on a flat, level surface.
- Take the Glass Table Top (H) and lower it gently onto the circular Table Top Frame (F) as shown in the diagram.
Step 5: Final Check and Assembly Complete
- Check that all M6×20 Bolts (J) are securely tightened using the Allen Key (K) and that the Table Legs (G) are firmly attached to the Table Top Frame (F).
- Confirm that the Glass Table Top (H) is properly centered and sitting flat within the frame.
The table assembly is now complete and ready for use.
Assembly Complete
Both rocking chairs and the glass-top table are now fully assembled.
Place the chairs and table on a flat, level surface and ensure all components are stable and properly aligned. Test the rocking motion of each chair gently to confirm smooth and balanced movement.
Verify that all bolts are securely tightened. Your Outsunny Rocking Chair & Glass Table Set is now ready for use.
Troubleshooting Guide
| Issue | Possible Cause | Solution |
| Chair feels unstable | Bolts not evenly tightened | Retighten all bolts evenly |
| Rocking motion uneven | Frame misalignment | Loosen bolts slightly, realign, retighten |
| Table wobbles | Uneven floor surface | Move to a level surface |
| Glass top shifts | Not centered properly | Reposition carefully |
Care & Maintenance
- Wipe metal frames regularly with a soft, dry cloth
- Clean glass using a non-abrasive glass cleaner
- Avoid harsh chemicals that may damage the finish
- Store in a dry area or use protective covers during prolonged exposure to weather
With its curved rocking base and coordinated glass-top table, this Outsunny Rocking Chair & Glass Table Set (SKU:863-128V00MX) set delivers balanced comfort and reliable structural support. Assembling each component carefully and tightening hardware evenly ensures long-term durability and smooth rocking performance.
You can also download the official Outsunny Rocking Chair & Glass Table Set assembly manual for your reference.
FAQs
Rocking chairs perform best on flat, level ground to maintain smooth and balanced motion. Uneven surfaces can cause instability, frame stress, or uneven rocking. If the area is slightly uneven, reposition the set or use leveling pads for better stability.
Wipe the frame regularly with a soft cloth and keep hardware tightened to prevent movement. Avoid harsh cleaners that may damage the protective coating. During prolonged bad weather, use covers or store the chairs in a dry space.
A properly assembled glass-top table is stable under normal conditions, but strong winds can shift lightweight furniture. Place the set in a sheltered location during storms. Regularly check that the glass panel is centered and secure within the frame.
Rocking chair sets can fit smaller balconies if there is enough clearance for the backward and forward motion. Measure both floor space and rocking range before placement. Position the chairs away from walls or railings to prevent contact while in use.