The Seville Cocktail Table (SKU:F-CYS-W48720760) is a living room coffee table featuring a tempered beveled glass top, marble paper finish, and powder-coated metal legs. It measures 52″ L x 32″ W x 20.5″ H and assembles in five steps using only the included tools and hardware.
Important Notes Before You Start
- Lay out all parts on a clean, flat surface and check them against the parts list below.
- Do not tighten any bolt until all assembly steps are fully completed, finger-tighten first, fully tighten at the very end.
- Place the Top Frame face-down on a soft surface (blanket or cardboard) during early steps to protect the finish.
- Keep all small hardware away from young children.
- Clean the table only with a soft cloth. No harsh chemicals.
Parts List
| Code | Part Name | Qty |
| A | Top Frame | 1 |
| B | Shelf | 1 |
| C | Bottom Panel | 1 |
| D | Glass Top | 1 |
| E | Legs | 4 |
Hardware List
| No. | Hardware Name | Qty |
| 1 | Allen Bolt 1/4″ × 50mm | 4 |
| 2 | Allen Bolt 1/4″ × 28mm | 8 |
| 3 | Spring Washer 1/4″ | 12 |
| 4 | Flat Washer 1/4″ | 12 |
| 5 | Allen Key M4 | 1 |
Step-by-Step Assembly Instructions
Follow the steps below to assemble your Seville Cocktail Table (SKU:F-CYS-W48720760).
Step 1: Attach the Four Legs to the Top Frame
- Place the Top Frame (A) face-down on a soft, flat surface to protect the finish.
- Attach all four Legs (E) to the Top Frame (A) as shown in image.
- For each leg, slide one Flat Washer (No. 4) and one Spring Washer (No. 3) onto an Allen Bolt 1/4″ × 28mm (No. 2).
- Drive the bolt in using the Allen Key M4 (No. 5).
Step 2: Attach the Shelf to the Legs
- Keep the frame upside down with all four legs attached.
- Position the Shelf (B) between the legs.
- Align the bolt holes on the Shelf with the holes on each Leg.
- At each connection point, slide one Spring Washer (No. 3) and one Flat Washer (No. 4) onto an Allen Bolt 1/4″ × 28mm (No. 2).
- Drive each bolt in using the Allen Key M4 (No. 5).
Step 3: Attach the Bottom Panel to the Legs
- Position the Bottom Panel (C) at the base of the four Legs.
- This step uses the longer 50mm bolts, needed here because of the extra depth through the leg structure.
- At each corner, slide one Spring Washer (No. 3) and one Flat Washer (No. 4) onto an Allen Bolt 1/4″ × 50mm (No. 1).
- Drive each bolt in using the Allen Key M4 (No. 5).
Step 4: Flip the Table and Insert the Glass Top
- Turn the entire table over so it stands upright on all four legs.
- Go around every bolt on the table, legs, shelf, and bottom panel, and tighten them all carefully using the Allen Key M4.
- Once all bolts are fully tightened, carefully lift the Glass Top (D) with both hands.
- Lower the Glass Top (D) down into the Top Frame (A).
- The glass sits inside the frame with no bolts required.
- Set it down slowly and make sure it seats evenly on all sides with no gap or overhang.
Step 5: Assembly is Completed
Stand back and check that the table looks right from all sides. Run through this quick check before use:
- All four legs sit flat on the floor with no rocking.
- The glass top sits evenly inside the frame with no tilt or gap on any side.
- No bolts feel loose, use the Allen Key M4 to re-tighten anything that moves.
- The table feels solid when you gently push it from the side.
Your Seville Cocktail Table is now fully assembled and ready to use.
Safety and Usage Notes
- This table is designed for indoor living room use only.
- Do not place excessive weight on one side of the glass top.
- The glass top is tempered, which means it is significantly stronger than standard glass, but it is not indestructible. Avoid dropping heavy or sharp objects directly onto it.
- Never use abrasive cleaners, rough sponges, or chemical sprays on the glass or the metal frame.
- Keep the table away from areas where children might run into the glass edge.
Maintenance Tips
- Glass top: Wipe with a soft, lint-free cloth. For smudges, a small amount of glass cleaner on the cloth works fine, spray the cloth, not directly onto the glass.
- Metal legs and frame: Wipe down with a damp soft cloth. The powder-coated finish resists rust, but avoids leaving moisture sitting on the surface for long periods.
- Bolts: Every few months, check all bolts with the included Allen key and re-tighten anything that has worked loose. Normal use causes minor vibration that can slowly back bolts out over time.
Customer Support & Assistance
If you experienced any difficulty during assembly or discovered a missing or damaged part, please contact Aosom Customer Support. Our team is committed to resolving the issue quickly and ensuring you are fully satisfied with your purchase.
You can also download the full Seville Cocktail Table (SKU:F-CYS-W48720760) assembly manual for reference.
FAQs
Neither. The glass top rests inside the top frame by gravity and fit. There are no clips, adhesives, or bolts holding it in place. This is intentional, it allows the glass to be lifted out easily for cleaning or moving.
No. The allen key M4 included in the box is the only tool required for all five steps. You do not need a screwdriver, drill, or wrench. However, having a soft blanket or piece of cardboard nearby to protect the finish while working is strongly recommended.
Tempered glass handles moderate heat, but placing very hot mugs, teapots, or candles directly on the surface repeatedly can cause thermal stress over time. Always use coasters or a heat-resistant mat. This also protects the beveled edges, which are the most vulnerable part of the glass to sudden temperature changes.