Outsunny Outdoor Wicker Rocking Chair Assembly Manual (SKU:867-048GY)

A grey wicker rocking chair with grey cushions on a wooden deck next to a pool.

The Outsunny Rocking Chair is designed to provide a relaxing seating experience with a smooth rocking base, supportive armrests, and comfortable cushions. Built with a sturdy frame and woven seat panel, this chair combines durability with comfort. By following the steps below carefully, assembly can be completed efficiently and safely.

Safety & Preparation

Before you begin, please follow these important safety guidelines:

Assembly should be completed by at least two adults.
Always assemble on a clean, flat, and dry surface.
Keep children away during assembly.
Avoid confusing similar bolts and hardware pieces.
Regularly check all fittings after assembly and tighten if needed.
Do not overload the chair or use it during severe weather conditions.

Unboxing: Parts Included

Check that all parts are included before starting assembly.

Parts List

Diagram of assembly parts including chair panels, cushions, screws, washers, and an Allen key.

Code	Part Name	Quantity
A	Left Armrest	1
B	Right Armrest	1
C	Seat Panel (Woven Base)	1
D	Backrest Panel	1
E	Seat Cushion	1
F	Backrest Pillow	1
G	Short Bolt (M6×35)	7 (+1 spare)
H	Long Bolt (M6×45)	4 (+1 spare)
J	Plastic Bolt Cap	11
K	Metal Washer	11 (+1 spare)
I	Allen Key	1

Step-by-Step Assembly Instructions

Step 1: Attach Seat Panel to Left Armrest

Diagram showing a seat panel being bolted to a left-side rocking chair armrest.

Place the Left Armrest (A) on a flat, stable surface.
Position the Seat Panel (C) so it aligns with the inner connection points of Part A.
Insert the Short Bolts M6×35(G) through the Metal Washers (K) into the aligned holes.
Use the Allen Key (I) to tighten the bolts lightly, keeping them slightly loose for later adjustment.

Note: When the rocking chair is fully assembled and all bolts are tightened, use the Plastic Bolt Caps (J) to cover the bolts.

Step 2: Attach Right Armrest

Assembly diagram illustrating the attachment of the right rocking armrest to the seat base.

Take the Right Armrest (B) and position it on the opposite side of the Seat Panel (C).
Align the connection points of Part B with the open side of the seat frame.
Insert the Short Bolts M6×35(G) through the Metal Washers (K) into the aligned holes.
Use the Allen Key (I) to tighten the bolts lightly, keeping them slightly loose for proper alignment.

Step 3: Install the Backrest Panel

Technical drawing showing the backrest panel being aligned and bolted to the chair frame.

Position the Backrest Panel (D) between the Left Armrest (A) and Right Armrest (B).
Align the mounting holes of the backrest with the side frame connection points as shown in image.
Insert the Long Bolts M6×45(H) through the Metal Washers (K) into the aligned four holes.
Use the Allen Key (I) to tighten all bolts evenly until the backrest is firmly secured.

Step 4: Secure the Backrest Panel

Diagram detailing the final screw installation to secure the upper backrest to the armrests.

Check the alignment of the Backrest Panel (D) with the chair frame.
Insert the Short Bolts (G – M6×35) through the Metal Washers (K) into the remaining middle connection point of the Backrest Panel (D) and Seat Panel (C), as shown in the image.
Use the Allen Key (I) to tighten firmly. Then check all bolts again and fully tighten them.
Finally, use the Plastic Bolt Caps (J) to cover all bolts.

Step 5: Place Cushions & Backrest Pillow

Illustration showing the placement of the seat cushion and button-tufted back pillow.

Take the Seat Cushion (E) and place it evenly on the Seat Panel (C).
Position the Backrest Pillow (F) against the Backrest Panel (D).
Adjust both cushions to ensure they sit properly and provide comfortable support.

Final Step: Assembly Complete

Line drawing of the fully assembled wicker rocking chair with all cushions in place.

Ensure all bolts are fully tightened using the Allen Key (I).
Check that the frame is stable and all connections are secure.
Confirm the rocking base sits evenly on the floor.
Adjust the Seat Cushion (E) and Backrest Pillow (F) if needed for comfort.

Your rocking chair is now fully assembled and ready for use.

Troubleshooting Guide

Issue	Possible Cause	Solution
Chair feels unstable	Bolts not fully tightened	Recheck and tighten all bolts
Parts not aligning	Frame assembled loosely	Adjust alignment before tightening
Backrest feels loose	Long bolts not secured	Tighten bolts (H) properly
Rocking not smooth	Uneven surface	Place chair on flat ground

Care & Maintenance

Clean using a soft cloth; avoid harsh chemicals.
Keep cushions dry and store indoors during bad weather.
Remove dirt, leaves, or water regularly.
Cover the chair when not in use to extend lifespan.
Periodically check all bolts and fittings.

With proper assembly and regular maintenance, this Outdoor Wicker Rocking Chair will provide long-lasting comfort and relaxation.

You can also download the Outsunny Outdoor Wicker Rocking Chair (SKU:867-048GY) assembly manual for your reference.

Download Manual(PDF)

FAQs

1. Is a wicker rocking chair comfortable for long sitting?

Yes, wicker rocking chairs are designed with supportive backrests and soft cushions for extended comfort. The gentle rocking motion helps reduce pressure on your back and promotes relaxation. Choosing a well-padded design makes long sitting more enjoyable.

2. What is the best material for a wicker rocking chair frame?

Powder-coated steel and aluminum are the best choices for strength and durability. These materials resist rust and provide stable, smooth rocking support over time. A solid frame ensures safety and long-term performance.

3. Are wicker rocking chairs suitable for small spaces?

Yes, many wicker rocking chairs are designed with compact dimensions for balconies or smaller patios. Their slim structure allows easy placement without overcrowding the area. Proper spacing ensures comfortable movement while rocking.